DENAILING METAL DETECTORS
  • Home
  • Shop
  • Videos
  • Uses, Curiosities, Support
  • Contact
  • Little Wizard 2
  • Lumber Wizard 5
  • Detecteur Bois
  • Detector para Carpintería
  • Home
  • Shop
  • Videos
  • Uses, Curiosities, Support
  • Contact
  • Little Wizard 2
  • Lumber Wizard 5
  • Detecteur Bois
  • Detector para Carpintería
Search
© 2023 Billy Carmen and ChatGPT

How to Tune a Little Wizard II Woodworking Metal Detector

4/1/2023

0 Comments

 
Picture
Keeping your Little Wizard II Woodworking Metal Detector tuned and by using a brand new fully charged 9-volt battery the detection power and its sensing depth will be at their optimal stages providing the user with the best metal detection for wood and other non-metallic surfaces. 

Below are detailed instructions on how to fine-tune and use the Little Wizard II Woodworking Metal Detector. This information will be helpful for those looking to use this device effectively in their woodworking projects.

​
​​To summarize the key points for fine-tuning and operating the Little Wizard II:
  1. Check the battery power: Ensure that you have at least 8.4 volts of battery power before starting. It's always a good idea to use a new battery.
  2. Turn on the device: Rotate the on/off/adjustment dial to the halfway point.
  3. Fine-tune the device: If the device is beeping at the halfway point, rotate the fine-tuning adjustment screw on the top of the unit until it stops beeping. Then, use the on/off/adjustment dial to find the point between where it beeps and stops beeping. This is typically the best point for adjustment. Users should experiment with different adjustment points for optimal detection.
  4. Test the device: Test the Little Wizard II on some visible metal and different-sized metal pieces to verify its detection capabilities and get accustomed to detection depths.
  5. Scan the wood: Slowly and steadily move the Little Wizard II across the surface of the wood, ensuring that the scanning surface remains in contact with the wood.
  6. Listen for alerts: Pay close attention to the audible alerts and LED lights when the device detects metal objects.
  7. Identify and mark the location: Go over the alerted area to pinpoint the exact location of the metal object and mark the spot.
  8. Remove the metal: Use appropriate tools to carefully remove the metal from the wood.
  9. Re-scan (if needed): After removing the detected metal, re-scan the wood to ensure no other hidden metal objects remain.
  10. Turn off the device: Press the power button to turn off the Little Wizard II and conserve battery life for your next project.
By following these steps, users can effectively fine-tune and operate the Little Wizard II Woodworking Metal Detector, ensuring the safety of their tools and the success of their woodworking projects.

​
0 Comments



Leave a Reply.

    Click Here To Buy Wizard Detectors
    ​On Amazon
    Little Wizard Tech Support
    Lumber Wizard Tech Support

    Scribes

    Written by ChatGPT with guidance from Billy Carmen.

    Past Blog Posts

    June 2023
    May 2023
    April 2023
    March 2023
    February 2023
    January 2023
    December 2022
    November 2022

    View my profile on LinkedIn

    This website uses marketing and tracking technologies. Opting out of this will opt you out of all cookies, except for those needed to run the website. Note that some products may not work as well without tracking cookies.

    Opt Out of Cookies
⚠️ WARNING:
This product can expose you to chemicals including [specific chemical(s), e.g., lead, BPA, or phthalates], which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.​

Site copyright 
© Wizard Industries Inc. USA 1999-2023.    Powered by Weebly.  Managed by Directnic
  • Home
  • Shop
  • Videos
  • Uses, Curiosities, Support
  • Contact
  • Little Wizard 2
  • Lumber Wizard 5
  • Detecteur Bois
  • Detector para Carpintería